冷却 - 关于冷却的双语例句 - 冷却造句 - 语文书

为您找到82个与“冷却”相关的双语例句：

We will improve the water level control of the water reservior.
我们将改进冷却水储水罐水位控制方式.
Skim the scum off the jam and let it cool.
撇去果酱上的浮沫，让它冷却。
In large multi - fluid cooling system, power maladjustment is very severe.
大型、多热源的冷却系统中, 存在比较严重的水力失调现象.
It must be cooled to its liquefaction temperature.
它必须冷却到其液化温度.
It didn't come as a shock to learn that the fuel and cooling systems are the most common causes of breakdown...
燃油和冷却系统是造成故障的最常见的原因，这一点不奇怪。
The special designed cooling barrel jacketing has a large heat conduction area and good cooling effect.
特殊设计的冷却桶夹套,热传道面积大,冷却效果极佳.
For example, water circulate constantly through the tuyere, hearth staves , bosh and inwall cooling plate etc.
例如, 冷却水不停地在风口、炉身、炉腹和内壁冷却板等部位循环流动.
Causes for the corrosion leakage of interstage coolers of a chlorine gas compressor were analyzed.
分析了氯气压缩机段间冷却器腐蚀泄漏原因,介绍了超声波防垢原理及其实施效果.
Take compressor's intercooler for example, main reasons of failure is analyzed.
以压缩机管壳式冷却器为例, 分析了其失效原因.
Hexahedral ice convenient interface, rapid cooling can drink and tastes better.
六面体冰块使用方便,接触面大, 可使饮料迅速冷却,口味更佳.
When an aqueous solution of the protein gelation is cooled, a polyer gel is formed.
蛋白质明胶水溶液冷却时形成聚合体凝胶.
Understands high efficiency gating and gradient cooling techniques via mold insulation wrapping.
懂得通过在模壳上包裹耐火石棉来达到高效率的浇口系统和梯度冷却效果.
Place the apparatus in a fume cupboard and cool the solution in ice.
将仪器放在通风的橱中,用冰冷却溶液.
The gas can be cooled by a heat exchanger after the air heater.
烟气可以用空气加热器后的热交换器来冷却.
It is then known as an evaporative cooler.
这就是当时人们所熟悉的蒸发式冷却器.
The direct type of evaporative air cooler uses primary wet surfaces.
直接蒸发式空气冷却器是利用原有的湿表面工作的.
If you evaporate a little sea water on a porcelain dish ; on cooling, crystals of common salt will deposit on the sides of the dish.
如果你将少许海水放到瓷盘中蒸发,冷却后就会有普通食盐的结晶附着在盘的四周.
INTECH COOLANT SE 18 EP is a high performance, semi - synthetic water - soluble metalworking fluid.
EP是一种极压型半合成水溶性冷却加工液.
Plastic injection mould - coolant passages, eject pin and electrical heating holes.
塑胶射出模具 - 冷却水孔、射梢孔及电热孔.
Plastic injection mould , coolant passages, eject pin and electrical heating holes.
塑胶射出模具?冷却水孔、射梢孔及电热孔.

|<<<1 234 5 >>>|